Ipcop V2 0 0 Installation Manual Pdf What is IPCop. The IPCop Firewall is a Linux firewall distribution. It is geared towards home and SOHO users.
• ICOP 20/20 VISION™ Supervisor Setup Manual (Part Number 700-00266) Rev. Website blue film yang belum diblokir. August, 2011 ICOP A Safety Vision Company 6100 W. Sam Houston Pkwy. Houston, Texas 77041 USA Main: 713.896.6600 Toll Free: 800.880.8855 Fax: 713.896.6640 www.ICOP.com T echSupport@ICOP.com. • The information in this document is subject to change without notice. Trademarks ICOP 20/20 VISION™ is a registered trademark exclusively owned and controlled by Safety Vision, LLC, Houston, Texas.
All other trademarks are the property of their owners. • Setting the Event IDs. 26 Reason For Stop ID..27 Race Type ID..28 Configuring the ICOP 20/20 VISION for Wireless Upload.29 Configuring the Wireless 1000g Setting.29 Configuring the Wireless Upload Timeout Setting.31 Configuring Wireless Upload. • SUPERVISOR SETUP MANUAL Restoring ICOP 20/20 VISION System Defaults. 39 Logging Out of Supervisor Setup.40 Auxiliary Control Unit.
41 Starting and Stopping a Recording Using the Auxiliary Control Unit.41 Inserting Marks in Video Recording.41 Contact Information. • Accessory fuse that provides power to the DVR must be pulled from the vehicle fuse box. Failure to remove this fuse may cause damage to the ICOP 20/20 VISION and void your warranty. IMPORTANT You must shut down the ICOP 20/20 VISION software before removing the USB cable from the MDT. • BEFORE YOU BEGIN The information in this document intends to give supervisors a cursory knowledge of the ICOP 20/20 VISION, and the user privileges that can be set. For more information regarding the functionality available with the DVR, please see the ICOP 20/20 VISION User Manual (Part Number 700-00271).
• ICOP 20/20 VISION™ SYSTEM REQUIREMENTS 32 bit Microsoft Vista or Microsoft XP operating system Minimum resolution of (800x600) Minimum 1.8 GHz processor Minimum 1 GB of RAM for XP or 2 GB of RAM for Vista . • SUPERVISOR SETUP MANUAL POWER ON SETTING SWITCH The ICOP 20/20 VISION can be powered on two different ways: using the ignition, or by turning it on manually. To select how the unit is powered on, you must place the power on setting switch in one of two positions. • The recording must stopped for power-saver mode to be activated. Important Whether the switch is in position 1 or 2, the ICOP 20/20 VISION must be turned off manually. Power-saver functionality takes affect after the last function has been performed by the unit. Revision: 005.
The software can enhance your images with special and audio effects providing viewing, editing, animation and measuring ability. You can get creative. 
• Front View of the ICOP 20/20 VISION (Fig. 2) Power: Powers the ICOP 20/20 VISION on and off manually. To power off the ICOP 20/20 VISION, press and hold Power for three seconds or until you hear a beep, then immediately release the key. • ICOP 20/20 VISION™ POWERING ON THE ICOP 20/20 VISION To power on the ICOP 20/20 VISION, complete the following steps: Step 1 Double-click the ICOP 20/20 VISION icon ( ) found on the desktop or single-click the icon in system tray. The ICOP 20/20 VISION interface appears.
• SUPERVISOR SETUP MANUAL ICOP 20/20 VISION INITIALIZATION After the ICOP 20/20 VISION is powered on it goes through an initialization process. During this process the unit locates the last recorded event and searches for a starting point. When a starting point it is found the monitor shows the. • ICOP 20/20 VISION™ LOGGING IN AS A SUPERVISOR To access the Supervisor Menu, complete the following steps: Note: You can access the Input User Password screen when the DVR initializes after being powered on; or by opening the Main Menu screen and selecting User Password. • SUPERVISOR SETUP MANUAL Step 2 The default Supervisor password is ADMIN. Enter the password using the MDT keyboard or by clicking the alphanumeric keys found near the lower part of the control. Multiple clicks of the alphanumeric keys change the key value.